Duct Tools

MODEL #DESCRIPTIONPHOTO
MA71250

  • Ideal for reducing diameter of round duct, sheet metal pipe, and downspouts for insertion into other pipes.
  • Five blades make uniform crimps on sheet metal up to 20 gauge
  • Recommended for light or heavy piping — furnace, smoke, and wall stacks, air ducts, water heater vent pipes, and downspouts.
  • Crimps up to 1-5/8″ for good overlap connection.
  • Heat treated blades for longer wear, hardened pivot bolt for durability, vinyl grips for comfort.
  • For natural in-draw on metal, always start with the three blades on top.
  • 9-3/4″ length, 1-5/8″ crimp
  • Straight handles with orange grips
MA71250 Klenk Crimper
MA71260

  • Ideal for reducing diameter of round duct, sheet metal pipe, and downspouts for insertion into other pipes.
  • Five blades make uniform crimps on sheet metal up to 20 gauge
  • Recommended for light or heavy piping — furnace, smoke, and wall stacks, air ducts, water heater vent pipes, and downspouts.
  • Crimps up to 1-5/8″ for good overlap connection.
  • Heat treated blades for longer wear, hardened pivot bolt for durability, vinyl grips for comfort.
  • For natural in-draw on metal, always start with the three blades on top.
  • 9-3/4″ length, 1-5/8″ crimp
  • Offset handles with orange grips
MA71260 Klenk Crimper
MA71500

  • Cuts round, oval, and black pipe and downspout
  • Pushing center blade point through pipe starts cut — this three-blade tool takes out a 1/8″ track leaving both ends clean and straight.
  • Maximum opening of jaws provides better bite — minimum opening of spring-back handles provides easier cutting.
  • Made from durable, hardened steel, and hardened pivot bolt provides long wear.
  • Non-slip handle grips are comfortable and secure.
  • 10-1/2″ length, 1-1/4″ cut

NOTE: A regular aviation snip used to cut pipe would bend up one side significantly. Klenk’s pipe cutter allows for this by making room for the tool to travel, leaving both sides clean and straight.

 

MA71500 Klenk Pipe Cutter
MA77000

  • Drop forged jaw
  • Compound leverage handles
  • Notches cleanly without slipping
  • Non-slip grips on handles
  • Cutting capacity of up to 22 gauge CR
  • 8-1/2″ length, 3/4″ notch
MA77000 Klenk Notcher
MA77010

  • Drop forged jaw
  • Compound leverage handles
  • Non-slip grips on handles
  • 8″ length, 3/8″ depth
MA77010 Klenk Snap Lock Punch
MA73010

Klenk’s Duct Slicer slices safely through metal duct and works great for take-offs!

  • Bevel on tip: Beveled edge notch on the tip allows easier and more accurate piercing of sheet metal.
  • Improved heat-treated steel shaft: Provides durability and longer-lasting edge on tip.
  • Ergonomic handle: Contoured, rubberized grip on handle exterior gives users a more comfortable and secure grip.
  • Shock-absorbing handle: Re-engineered internal structure and steel end cap strengthens handle and absorbs shock when the tool is struck, decreasing hand fatigue.
  • 12″ overall length

MA73010 Klenk Duct Slicer
MA77530

Engineered to hold duct in place when fastening duct work!

  • Holds duct in place with one hand while slipping drive cleat in place with other hand.
  • Engineered to be used even in tight or cramped areas, the offset duct stretcher provides leverage and saves your knuckles when working in awkward spaces.
  • Wheels adjust to span greater distances using the additional spacing holes.
  • Anodized aluminum body has vinyl cushion grip handle.
  • 16″ length, 1-3/8″ wide

MA77530 Klenk Duct Stretcher